Homemade Combustion Chamber and Turbine for Jet Engine
Articles Blog

Homemade Combustion Chamber and Turbine for Jet Engine

November 20, 2019


Thank you for watching, if you enjoyed this YouTube video, please leave a thumbs up and subscribe to my channel, as I’ll be making more content. I’ve left a link to my Twitter account so be sure to follow me, as I’ll use it to post pictures and updates on the status of upcoming videos

Only registered users can comment.

  1. Wonderful ingeneous wiork, But why aren't you creating aerofoil blades instead of flat ones:
    That way you could probably at least double the Efficiency of your engine 😉 (see my earlier comment)

  2. How long have you progressed your project?
    How much time do you devote to building this?
    How many pounds do you have to push?
    Could you share with me your plans?

  3. How long have you progressed your project?
    How much time do you devote to building this?
    How many pounds do you have to push?
    Could you share with me your plans?

  4. How long have you progressed your project?
    How much time do you devote to building this?
    How many pounds do you have to push?
    Could you share with me your plans?

  5. wow dude Amazing! let me ask you, at the end you didn't explain, but the pump used and its setup? what about those small tubes that goes to the combustion chamber? the fuel lines i guess what size and spec please?

  6. Unless your turbine blades are aerodynamicc aerofoils your operating efficiency is less than 30%.Your Kochtopf is super but you need to address the rotor/stator issue

  7. jet engines produce he thrust by high speed and pressure air.The real jet engine is compressing air by the opposite thrust fans and reduce the space of tube,then the air will flow in small space and be compressed.the compress air can be burn with fuel and stronger?

  8. Very cool 'fir-tree' airfoil restraints like the pros, which brings a question, what is your RPM limitation?I was once that motivated, check out – rocket testing by ken mason. Air-breathers and rockets, cool combo. Hope to meet someday, if not here on the other side.
    Thanks again – Ken

  9. Stainless steel isn't good enough in a combustor. Repeated heating cooling cycles, it won't last long at all….Inconel my friend, 800C will eat Stainless Steel. Don't worry though, it doesn't have a hope in hell of ever running. …Sorry, it's just the reality of an Axial at this size..If you made the Turbine wheels from Stainless, they will explode too….Inconel….Inconel…Inconel.

  10. Fuck that shit, That is not a turbine, its a fucking stove. Where are the spinning blades!!!!! Youtube please remove this video and thumbs down for clickbait video

  11. sir can you please tell me the approximate weight of the combustion chamber and material used for it.
    Thanks in anticipation.

  12. Stator is missing, the stator is an important part of a turbine or of a turbo compressor.

    Most people are looking to the schematic drawings of a turbojet, and most of these simplified drawings doesn't explain much …

  13. that will not survive, a) centrifugal forces, b) egt temp, make sure you stand clear when spooling up, how did you calculate the compression ratio you have a few stages there in the LP HP section

  14. What a great bit of work. Ignore the ‘why haven’t you done this or that brigade’ give this guy a break, he’s probably in the r and d stage.

  15. What about a Tesla turbine? Terrible startup efficiency, but depending on application, efficient and capable.

  16. I think this is a waste of time.
    No air foil profile on the blades, no stator blades.
    Not balanced, many have tryed, very few have working turbine.

  17. bro I don't have a lathe machine like you to make so accurate blades. Please help me with some suggestions. I am trying to build one . PLZ REPLY!!!!!

  18. Say i use metal, steel or iron for a chamber like yours, If i use hydrogen gas, then if i decide to make a small jet and fly it for 30 min, won't the temperature get hot and how to prevent it?

  19. There's the guy saying that you build a nice stove before I read that I was thinking about the same thing

  20. the way to make high impulse thrust is to have a very high heat chamber and inject a liquid into it that vaporizes and exits the rear at a high velocity. Its not necessary to have all those spinning parts, just a high heat vaporizer chamber and inject a liquid into it.

Leave a Reply

Your email address will not be published. Required fields are marked *